1What is the primary meaning of the term 'Orthographic'?
A.Parallel view
B.Angular projection
C.Right-angled drawing
D.Straight writing
Correct Answer: Right-angled drawing
Explanation:
'Ortho' means right angle and 'graphic' means drawing or description. It implies projections are perpendicular to the plane.
Incorrect! Try again.
2In orthographic projection, the projectors are drawn ____ to the plane of projection.
A.Parallel
B.Inclined at 45 degrees
C.Perpendicular
D.Tangent
Correct Answer: Perpendicular
Explanation:
The defining characteristic of orthographic projection is that the lines of sight (projectors) strike the projection plane at a 90-degree angle.
Incorrect! Try again.
3Where is the observer assumed to be located in an orthographic projection?
A.Touching the plane
B.At an infinite distance
C.At a finite distance
D.Inside the object
Correct Answer: At an infinite distance
Explanation:
To ensure projectors are parallel to each other and perpendicular to the plane, the observer is assumed to be at infinity.
Incorrect! Try again.
4The two principal planes of projection are usually designated as:
A.Vertical Plane (VP) and Profile Plane (PP)
B.Auxiliary Plane (AP) and Vertical Plane (VP)
C.Horizontal Plane (HP) and Vertical Plane (VP)
D.Ground Plane (GP) and Picture Plane (PP)
Correct Answer: Horizontal Plane (HP) and Vertical Plane (VP)
Explanation:
The HP and VP are the primary reference planes that intersect at the XY line to form quadrants.
Incorrect! Try again.
5The Front View of an object is projected onto which plane?
A.Horizontal Plane
B.Auxiliary Plane
C.Profile Plane
D.Vertical Plane
Correct Answer: Vertical Plane
Explanation:
The Front View (Elevation) is viewed from the front and projected onto the Vertical Plane located behind or in front of the object.
Incorrect! Try again.
6In standard orthographic projection, the intersection of the Horizontal Plane and Vertical Plane is called the:
A.Projector Line
B.Profile Line
C.Reference Line (XY Line)
D.Trace Line
Correct Answer: Reference Line (XY Line)
Explanation:
The line of intersection between the HP and VP is the reference line, commonly labeled X-Y.
Incorrect! Try again.
7In First Angle Projection, the object is positioned in which quadrant?
A.Third Quadrant
B.Second Quadrant
C.First Quadrant
D.Fourth Quadrant
Correct Answer: First Quadrant
Explanation:
First Angle Projection assumes the object is placed in the first quadrant, where the object is between the observer and the projection plane.
Incorrect! Try again.
8In Third Angle Projection, what is the relative position of the plane of projection?
A.Perpendicular to the observer only
B.Irrelevant
C.Behind the object
D.Between the observer and the object
Correct Answer: Between the observer and the object
Explanation:
In Third Angle Projection, the plane of projection is assumed to be transparent and placed between the observer and the object.
Incorrect! Try again.
9When converting 3D to 2D in orthographic projection, how is the Horizontal Plane (HP) manipulated?
A.It is rotated 90 degrees counter-clockwise
B.It is folded upwards
C.It is rotated 90 degrees clockwise
D.It remains fixed
Correct Answer: It is rotated 90 degrees clockwise
Explanation:
To align the views on a single sheet of paper, the HP is rotated 90 degrees clockwise until it aligns with the VP.
Incorrect! Try again.
10In First Angle Projection, where is the Top View drawn relative to the Front View?
A.Above the Front View
B.To the left of the Front View
C.To the right of the Front View
D.Below the Front View
Correct Answer: Below the Front View
Explanation:
Because the object is in the 1st quadrant and HP rotates down, the Top View appears below the reference line (and the Front View).
Incorrect! Try again.
11In Third Angle Projection, where is the Top View drawn relative to the Front View?
A.Beside the Front View
B.Above the Front View
C.Below the Front View
D.Overlaying the Front View
Correct Answer: Above the Front View
Explanation:
In the 3rd quadrant, the HP is above the object. When rotated, the Top View projects upward, appearing above the Front View.
Incorrect! Try again.
12Which projection system is commonly used in the United States?
A.Third Angle Projection
B.First Angle Projection
C.Isometric Projection
D.Oblique Projection
Correct Answer: Third Angle Projection
Explanation:
The USA and Canada primarily use Third Angle Projection standard for engineering drawings.
Incorrect! Try again.
13The standard symbol for First Angle Projection looks like:
A.Two concentric circles on the left, a trapezoid on the right
B.A square and a circle
C.A trapezoid on the left, two concentric circles on the right
D.Two triangles
Correct Answer: Two concentric circles on the left, a trapezoid on the right
Explanation:
The symbol represents a frustum of a cone. In 1st angle, the circle (view from left) is projected to the right of the trapezoid (front view). However, standard placement usually shows the circle on the left if projecting the left side view to the right.
Incorrect! Try again.
14In First Angle Projection, the Left Side View is drawn on which side of the Front View?
A.Right side
B.Bottom side
C.Top side
D.Left side
Correct Answer: Right side
Explanation:
In 1st angle, the view is projected onto the plane behind the object. The Left Side View projects to the profile plane on the right.
Incorrect! Try again.
15Which line type is used to represent invisible edges in an orthographic drawing?
A.Phantom line
B.Center line
C.Hidden line (dashed)
D.Continuous thick line
Correct Answer: Hidden line (dashed)
Explanation:
Hidden lines (short dashes) are used to show features or edges that are not visible from the current viewing angle.
Incorrect! Try again.
16Which AutoCAD command is used to load and manage different line styles like Dashed or Center?
A.LINETYPE
B.LINE
C.LAYER
D.PROPERTIES
Correct Answer: LINETYPE
Explanation:
The LINETYPE command opens the manager to load specific styles like 'Hidden' or 'Center' into the drawing.
Incorrect! Try again.
17A Center Line is represented by:
A.Zig-zag line
B.Alternating long and short dashes
C.Short dashes only
D.Continuous thin line
Correct Answer: Alternating long and short dashes
Explanation:
Center lines denote axes of symmetry or centers of circles and consist of a chain of long and short dashes.
Incorrect! Try again.
18Which AutoCAD command allows you to move objects a specified distance in a specified direction?
A.PAN
B.COPY
C.ARRAY
D.MOVE
Correct Answer: MOVE
Explanation:
The MOVE command displaces objects without changing their orientation or size.
Incorrect! Try again.
19What is the shortcut key for the MOVE command in AutoCAD?
A.MO
B.M
C.MV
D.O
Correct Answer: M
Explanation:
M is the standard command alias for MOVE.
Incorrect! Try again.
20To rotate an object in AutoCAD, you must define a:
A.Scale factor
B.Displacement vector
C.Mirror line
D.Base point
Correct Answer: Base point
Explanation:
The Base Point is the pivot point around which the object rotates.
Incorrect! Try again.
21Positive rotation in AutoCAD is typically in which direction?
A.Upwards
B.Counter-Clockwise
C.Downwards
D.Clockwise
Correct Answer: Counter-Clockwise
Explanation:
By default in AutoCAD, angles are measured counter-clockwise from the positive X-axis.
Incorrect! Try again.
22Which command creates a duplicate of an object while leaving the original in place?
A.COPY
B.ROTATE
C.MOVE
D.MIRROR
Correct Answer: COPY
Explanation:
The COPY command functions identically to Move, but it creates a duplicate rather than displacing the original.
Incorrect! Try again.
23Which command is used to remove unwanted portions of a line that crosses another object?
A.DELETE
B.TRIM
C.ERASE
D.BREAK
Correct Answer: TRIM
Explanation:
TRIM cuts objects to meet the edges of other objects (cutting edges).
Incorrect! Try again.
24What is the shortcut key for the TRIM command in AutoCAD?
A.TR
B.TI
C.TM
D.T
Correct Answer: TR
Explanation:
TR is the standard command alias for TRIM.
Incorrect! Try again.
25Which command deletes an entire object from the drawing?
A.CUT
B.TRIM
C.REMOVE
D.ERASE
Correct Answer: ERASE
Explanation:
ERASE (shortcut E) removes selected objects completely from the drawing database.
Incorrect! Try again.
26To create a symmetrical copy of an object across a line, which command is used?
A.ARRAY
B.MIRROR
C.COPY
D.ROTATE
Correct Answer: MIRROR
Explanation:
MIRROR creates a reverse copy of the object across a specified axis (mirror line).
Incorrect! Try again.
27When using the MIRROR command, AutoCAD asks if you want to:
A.Rotate source objects
B.Erase source objects
C.Trim source objects
D.Scale the source object
Correct Answer: Erase source objects
Explanation:
After defining the mirror line, AutoCAD prompts 'Erase source objects? [Yes/No]'.
Incorrect! Try again.
28Which command changes the size of an object proportionally?
A.ZOOM
B.SCALE
C.EXTEND
D.STRETCH
Correct Answer: SCALE
Explanation:
The SCALE command enlarges or reduces selected objects equally in X, Y, and Z directions.
Incorrect! Try again.
29If you apply a Scale Factor of 0.5, the object will:
A.Rotate 50 degrees
B.Move 0.5 units
C.Reduce to half its size
D.Double in size
Correct Answer: Reduce to half its size
Explanation:
A scale factor less than 1 reduces the size; 0.5 makes it 50% of the original size.
Incorrect! Try again.
30Which command connects two objects with a tangent arc (rounded corner)?
A.FILLET
B.BLEND
C.CHAMFER
D.ARC
Correct Answer: FILLET
Explanation:
FILLET creates a rounded corner between two lines or curves using a specified radius.
Incorrect! Try again.
31If the Radius is set to 0 in the FILLET command, what is the result?
A.An error
B.No change
C.A sharp corner
D.A circular corner
Correct Answer: A sharp corner
Explanation:
Filleting with a radius of 0 is a common technique to trim or extend two lines to form a sharp intersection.
Incorrect! Try again.
32Which command connects two lines with a beveled (angled) corner?
A.CHAMFER
B.TRIM
C.EXTEND
D.FILLET
Correct Answer: CHAMFER
Explanation:
CHAMFER creates a straight line connection (bevel) between two non-parallel lines.
Incorrect! Try again.
33To define a Chamfer, you usually specify:
A.Center point
B.Two distances or a distance and an angle
C.Radius
D.Diameter
Correct Answer: Two distances or a distance and an angle
Explanation:
Chamfers are defined by the distance cut back from the intersection on both lines, or one distance and the angle of the cut.
Incorrect! Try again.
34Which command creates multiple copies of an object in a pattern?
A.GROUP
B.MULTIPLE
C.COPY
D.ARRAY
Correct Answer: ARRAY
Explanation:
ARRAY distributes object copies in Rectangular, Polar, or Path patterns.
Incorrect! Try again.
35In a Rectangular Array, the pattern is defined by:
A.Center point and angle
B.Path and items
C.Rows and Columns
D.Radius and axis
Correct Answer: Rows and Columns
Explanation:
Rectangular arrays are arranged in a grid format defined by the number of rows and columns and the spacing between them.
Incorrect! Try again.
36Which type of Array distributes objects around a center point?
A.Path
B.Polar
C.Circular
D.Rectangular
Correct Answer: Polar
Explanation:
Polar Array copies objects in a circular pattern around a specified center point.
Incorrect! Try again.
37When using the LTSCALE command, what are you adjusting?
A.The scale factor of the linetype pattern
B.The length of the line
C.The color of the line
D.The thickness of the line
Correct Answer: The scale factor of the linetype pattern
Explanation:
LTSCALE (LineType Scale) controls the global display scale of dashes and spaces in non-continuous lines.
Incorrect! Try again.
38In orthographic projection, if a surface is parallel to a plane of projection, its projection on that plane is:
A.A point
B.True shape and size
C.A line
D.Foreshortened
Correct Answer: True shape and size
Explanation:
When a surface is parallel to the viewing plane, the resulting view reflects the actual dimensions and shape of that surface.
Incorrect! Try again.
39In orthographic projection, if a surface is perpendicular to a plane of projection, it appears as:
A.A line
B.A point
C.Distorted
D.True shape
Correct Answer: A line
Explanation:
A surface viewed 'edge-on' (perpendicular to the view plane) projects as a single straight line.
Incorrect! Try again.
40In AutoCAD, to ensure lines are drawn perfectly horizontal or vertical, which mode should be ON?
A.OSNAP
B.SNAP
C.ORTHO
D.GRID
Correct Answer: ORTHO
Explanation:
Ortho mode (F8) restricts cursor movement to the horizontal (X) and vertical (Y) axes.
Incorrect! Try again.
41What is the function of Object Snap (OSNAP)?
A.Snaps to specific geometric points on objects
B.Snaps to grid points
C.Automatically dimensions the object
D.Restricts angle movement
Correct Answer: Snaps to specific geometric points on objects
Explanation:
OSNAP allows precise selection of geometric points like Endpoints, Midpoints, Centers, and Intersections.
Incorrect! Try again.
42When drawing orthographic views in AutoCAD, which command helps project features from one view to another accurately?
A.DONUT
B.ARC
C.SPLINE
D.XLINE (Construction Line)
Correct Answer: XLINE (Construction Line)
Explanation:
XLINE creates infinite lines used as construction guides to project widths, heights, and depths between views.
Incorrect! Try again.
43Which view usually gives the most information about the object?
A.Bottom View
B.Side View
C.Front View
D.Top View
Correct Answer: Front View
Explanation:
The Front View is typically chosen to show the maximum characteristics and dimensions (Length and Height) of the object.
Incorrect! Try again.
44The dimension showing the depth (width) of an object is common to which two views?
A.Front and Top
B.Top and Side
C.Front and Rear
D.Front and Side
Correct Answer: Top and Side
Explanation:
The Top view shows Length and Depth (Width); the Side view shows Height and Depth (Width).
Incorrect! Try again.
45In AutoCAD, which key allows you to quickly repeat the last used command?
A.Spacebar or Enter
B.Esc
C.Shift
D.Tab
Correct Answer: Spacebar or Enter
Explanation:
Pressing Spacebar or Enter immediately after a command finishes will re-invoke that same command.
Incorrect! Try again.
46What is the result of the EXPLODE command on an Array?
A.It hides the array
B.It deletes the array
C.It changes the array type
D.It converts the associative array into individual objects
Correct Answer: It converts the associative array into individual objects
Explanation:
Modern AutoCAD arrays are associative (grouped). EXPLODE breaks the group into independent objects.
Incorrect! Try again.
47Which AutoCAD command is used to restore the most recently erased objects?
A.REDO
B.RETURN
C.BACK
D.OOPS
Correct Answer: OOPS
Explanation:
OOPS restores objects erased by the last ERASE command, even if other commands were executed subsequently (unlike Undo).
Incorrect! Try again.
48A 'Miter Line' drawn at 45 degrees is used to transfer dimensions between:
A.Isometric and Orthographic
B.Front View and Side View
C.Front View and Top View
D.Top View and Side View
Correct Answer: Top View and Side View
Explanation:
A 45-degree miter line allows the transfer of depth dimensions from the Top View to the Side View (or vice versa) without measuring.
Incorrect! Try again.
49If a line is inclined to the HP and parallel to the VP, its Front View will be:
A.A point
B.True length and inclined
C.A horizontal line
D.A line shorter than true length
Correct Answer: True length and inclined
Explanation:
Since it is parallel to the VP, the projection on the VP (Front View) captures the true length and the inclination.
Incorrect! Try again.
50In AutoCAD, 'Window Selection' (dragging left to right) selects:
A.The last drawn object
B.Only objects completely inside the window
C.Anything the window touches
D.Only text objects
Correct Answer: Only objects completely inside the window
Explanation:
A blue window (Left to Right) selects only items fully enclosed. A green crossing window (Right to Left) selects anything touched.
Incorrect! Try again.
Did this save you a night before the exam?
LPU Notes is free, and it stays free. Ads cover part of the server bill.
The rest comes out of a student's own pocket: the domain, the storage,
and keeping the site up through the weeks everyone needs it at once.
The payment button didn't load. An ad blocker or a filtered network is the usual reason.
to try again.
Nothing here is ever locked, and nothing unlocks. Chip in only if it was worth it.
What it pays for →