Unit 5: Remote controller and Autopilot - Practice Quiz

ASE107 — Fundamental Of Drone Technology 60 Questions
0 Correct 0 Wrong 60 Left
0/60

1 What is the main purpose of a drone remote controller?

Basic Remote Controller Easy
A. To charge the drone battery
B. To send pilot commands to the drone
C. To record video on the drone
D. To measure the drone altitude

2 Which remote-controller control is commonly used to change a drone's direction and altitude?

Basic Remote Controller Easy
A. Trim covers
B. Antenna caps
C. Battery clips
D. Control sticks

3 What does the throttle control usually change on a multirotor drone?

Basic Remote Controller Easy
A. Camera focus
B. Motor speed
C. GPS accuracy
D. Radio frequency

4 Which part of a remote controller transmits radio signals?

Basic Remote Controller Easy
A. Antenna
B. Control stick
C. Battery door
D. Display

5 What is the primary function of a receiver on a drone?

Receiver Easy
A. Supply power to the motors
B. Measure pressure around the drone
C. Receive commands from the controller
D. Store images from the camera

6 Where is the radio receiver normally installed in a drone system?

Receiver Easy
A. Inside the charger
B. On the landing pad
C. On the drone
D. Inside the controller

7 What process connects a radio receiver with a specific remote controller?

Receiver Easy
A. Balancing
B. Charging
C. Binding
D. Calibrating

8 What is telemetry in a drone system?

Telemetry System Easy
A. Direct charging of batteries
B. Manual adjustment of propellers
C. Remote transmission of flight data
D. Physical protection of sensors

9 Which information is commonly sent through a drone telemetry system?

Telemetry System Easy
A. Landing-gear size
B. Frame material
C. Battery voltage
D. Propeller color

10 Why is telemetry useful to a drone pilot?

Telemetry System Easy
A. It reduces the drone weight
B. It increases propeller diameter
C. It repairs damaged motors
D. It displays flight status remotely

11 What is the main role of an autopilot system in a drone?

Introduction to autopilot System Easy
A. Attach and remove propellers
B. Paint and protect the frame
C. Charge and balance batteries
D. Control and stabilize flight

12 Which component is often called the brain of an autonomous drone?

Introduction to autopilot System Easy
A. Flight controller
B. Battery connector
C. Propeller guard
D. Landing gear

13 What can an autopilot use to follow a planned route?

Introduction to autopilot System Easy
A. Motor labels
B. GPS waypoints
C. Frame markings
D. Propeller numbers

14 What information does an autopilot process to maintain stable flight?

Introduction to autopilot System Easy
A. Package labels
B. Frame dimensions
C. Propeller colors
D. Sensor measurements

15 Which internal sensor measures a drone's angular rotation rate?

Internal Sensors Easy
A. GPS receiver
B. Optical-flow camera
C. Rangefinder
D. Gyroscope

16 Which internal sensor measures acceleration?

Internal Sensors Easy
A. Rangefinder
B. Magnetometer
C. Accelerometer
D. Thermometer

17 Which sensor uses air pressure to help estimate altitude?

Internal Sensors Easy
A. Gyroscope
B. Camera
C. Compass
D. Barometer

18 Which external sensor provides geographic position information?

External Sensors Easy
A. Accelerometer
B. GPS receiver
C. Gyroscope
D. Barometer

19 Which external sensor can measure the distance between a drone and an obstacle?

External Sensors Easy
A. Rangefinder
B. Barometer
C. Gyroscope
D. Accelerometer

20 What does an optical-flow sensor help a drone detect?

External Sensors Easy
A. Rotation speed of each motor
B. Pressure inside the controller
C. Movement relative to the ground
D. Voltage inside the battery

21 On a Mode 2 remote controller, a pilot wants to increase altitude without intentionally changing yaw, pitch, or roll. Which input should be applied?

Basic Remote Controller Medium
A. Move the right stick straight upward
B. Move the left stick straight downward
C. Move the right stick straight downward
D. Move the left stick straight upward

22 A drone responds too sharply to small stick movements near the center, but the pilot still needs full control authority at maximum stick deflection. Which transmitter adjustment is most appropriate?

Basic Remote Controller Medium
A. Reduce the endpoint setting
B. Increase positive exponential
C. Reverse the control channel
D. Increase the trim setting

23 During a preflight check, the flight controller shows only 80% input when the transmitter stick is at its maximum position. What should be checked first?

Basic Remote Controller Medium
A. The battery cell balancing
B. The GPS update frequency
C. The channel endpoint calibration
D. The propeller pitch angle

24 A receiver has two diversity antennas. How should their active sections generally be arranged to reduce signal loss caused by aircraft orientation?

Receiver Medium
A. Parallel and touching each other
B. Pointing toward the motors
C. At approximately right angles
D. Wrapped around the battery

25 What receiver configuration best protects a drone if the transmitter signal is lost during flight?

Receiver Medium
A. Increase receiver output voltage
B. Hold every channel indefinitely
C. Apply a predefined failsafe state
D. Disable all flight-controller sensors

26 After installing a new receiver, moving the roll stick changes the flight controller's yaw input. What is the most likely cause?

Receiver Medium
A. Excessive accelerometer vibration
B. Weak GPS satellite geometry
C. Incorrect receiver channel mapping
D. Incorrect propeller balancing

27 The drone still responds normally to control inputs, but battery voltage and position stop updating on the ground station. What is the most likely problem?

Telemetry System Medium
A. The motors have entered failsafe
B. The telemetry downlink has failed
C. The receiver has lost control power
D. The gyroscope has stopped measuring

28 During a long-range flight, telemetry RSSI steadily falls and packet-loss warnings appear. What is the most appropriate immediate response?

Telemetry System Medium
A. Increase distance to test the link
B. Raise the autopilot control gains
C. Improve line of sight and return closer
D. Disable telemetry error reporting

29 A telemetry system reports attitude only once per second. Why is it unsuitable for diagnosing a rapid oscillation occurring at ?

Telemetry System Medium
A. Its sampling rate is too low
B. Its antenna polarization is circular
C. Its receiver voltage is too stable
D. Its radio frequency is too high

30 A drone following a straight GPS route encounters a steady crosswind. What should a functioning autopilot do to remain on the route?

Introduction to autopilot System Medium
A. Ignore GPS until the wind stops
B. Command a compensating crab angle
C. Maintain heading without position correction
D. Reduce all motor speeds equally

31 In Stabilize mode, a drone levels itself when the sticks are centered but does not maintain altitude automatically. Why is this expected?

Introduction to autopilot System Medium
A. Stabilize mode disables the gyroscope
B. Stabilize mode requires no throttle input
C. Stabilize mode regulates attitude only
D. Stabilize mode controls GPS position only

32 After a metal payload is installed, the autopilot reports inconsistent compass readings during its pre-arm check. What should the operator do?

Introduction to autopilot System Medium
A. Bypass the warning and take off
B. Disable every navigation failsafe
C. Increase throttle during calibration
D. Identify interference and recalibrate

33 A stationary drone reports a slowly increasing yaw rate after its electronics warm up. Which action most directly addresses this behavior?

Internal Sensors Medium
A. Increase the GPS waypoint acceptance radius
B. Replace the telemetry antenna orientation
C. Calibrate the gyroscope at operating temperature
D. Reduce the optical-flow update frequency

34 Flight logs show high-frequency accelerometer noise that increases with motor speed. Which corrective action should be tried first?

Internal Sensors Medium
A. Lower the receiver failsafe delay
B. Balance the propellers and inspect mounts
C. Move the GPS waypoint farther away
D. Increase the compass declination value

35 A barometric altitude reading fluctuates whenever propeller airflow passes over the flight controller. What is the best mitigation?

Internal Sensors Medium
A. Mount the sensor directly below a propeller
B. Replace the barometer with a magnetometer
C. Shield the sensor while allowing static pressure
D. Seal the sensor inside an airtight enclosure

36 A drone's heading changes by several degrees when high motor current flows, although its physical direction is unchanged. What is the most likely cause?

Internal Sensors Medium
A. Magnetic interference near the compass
B. Control latency near the receiver
C. Satellite geometry near the GPS
D. Atmospheric pressure near the barometer

37 A drone operating between tall buildings shows sudden GPS position jumps despite tracking several satellites. Which effect most likely explains this?

External Sensors Medium
A. Multipath reflection of satellite signals
B. Gyroscope saturation from low throttle
C. Receiver failsafe from compass declination
D. Barometer drift from antenna polarization

38 For automatic landing close to the ground, which external sensor generally provides more precise direct height measurement than standard GPS?

External Sensors Medium
A. Motor current sensor
B. Radio-control receiver
C. Downward rangefinder
D. Three-axis magnetometer

39 An indoor drone using optical flow holds position over a patterned floor but drifts over a glossy, featureless floor. What is the best explanation?

External Sensors Medium
A. The camera lacks trackable visual features
B. The barometer measures excessive pressure
C. The receiver has too many output channels
D. The compass uses the wrong declination

40 A fixed-wing drone maintains a constant GPS ground speed while flying into stronger headwind. What should a correctly functioning airspeed sensor indicate?

External Sensors Medium
A. A higher airspeed than ground speed
B. A lower airspeed than ground speed
C. An airspeed always equal to ground speed
D. A zero airspeed during constant flight

41 A transmitter maps a centered stick input to pulse widths from to . It applies a symmetric deadband of and then rescales each remaining side so full stick still produces the endpoint. What pulse width should be transmitted for ?

Basic Remote Controller Hard
A.
B.
C.
D.

42 A pilot applies full roll and full pitch simultaneously. The transmitter independently maps both commands to motor-mixing inputs, causing the mixed outputs to exceed their allowed range. Which treatment best preserves the requested control direction while avoiding clipping distortion?

Basic Remote Controller Hard
A. Clip each mixed output independently at its nearest permitted limit
B. Scale both commands proportionally until every mixed output is within range
C. Apply additional exponential shaping after the outputs are clipped
D. Reduce only the pitch command until the roll outputs are valid

43 A remote-control link has a transmitter EIRP of , path loss of , receiver antenna gain of , and miscellaneous losses of . If receiver sensitivity is , what is the link margin?

Basic Remote Controller Hard
A.
B.
C.
D.

44 A serial RC receiver reports valid channel values for several frames after losing its RF link, but it also asserts a failsafe status flag. How should a safety-critical autopilot interpret these frames?

Receiver Hard
A. Average the held values until channel variance exceeds a configured threshold
B. Continue normal flight because the channel values remain syntactically valid
C. Enter failsafe because the explicit link-status flag overrides held channel data
D. Ignore the flag unless the throttle channel changes to its minimum value

45 A diversity receiver switches antennas whenever the alternate antenna's RSSI is momentarily higher. During flight, this produces frequent switching and bursts of lost frames. Which modification most directly addresses the problem?

Receiver Hard
A. Increase the commanded channel refresh rate without changing selection
B. Average both antenna signals electrically before decoding every frame
C. Select the antenna with the lower noise floor only during startup
D. Add RSSI hysteresis and require superiority for a minimum dwell time

46 Eight independent PWM receiver channels update at but begin their pulses at unrelated times. An autopilot reads each channel immediately after its edge arrives. What subtle control-input problem can result compared with decoding one framed serial packet?

Receiver Hard
A. The autopilot necessarily receives all eight channels at exactly one-eighth the update rate
B. The PWM pulse widths become proportional to RF carrier frequency rather than stick position
C. The receiver loses the ability to represent commands below the electrical midpoint
D. The assembled channel set can represent different sampling instants within one control cycle

47 A telemetry stream uses packet sequence numbers modulo . The last accepted number was , followed by packets numbered and . Assuming packets arrive in order, how many packets were lost before packet ?

Telemetry System Hard
A. One packet
B. Two packets
C. Three packets
D. Four packets

48 A half-duplex telemetry radio provides a raw rate of . Protocol overhead consumes of transmitted bits, and the air-time schedule assigns to downlink. What is the maximum downlink payload rate under continuous loading?

Telemetry System Hard
A.
B.
C.
D.

49 A ground station receives a delayed position packet after a newer packet because the radio retransmitted it. Which design best prevents the displayed vehicle position from moving backward in time?

Telemetry System Hard
A. Reset the position estimate whenever retransmission is detected on the link
B. Order updates by ground-station arrival times and display every valid packet
C. Order updates by vehicle timestamps and reject data older than the displayed state
D. Average consecutive positions whenever their packet sequence numbers differ

50 In a cascaded multirotor controller, the outer attitude loop produces a desired angular rate, while the inner rate loop commands torque. Why should the inner loop normally run at a substantially higher bandwidth?

Introduction to autopilot System Hard
A. It must estimate magnetic declination before attitude corrections become observable
B. It must lower motor update frequency to suppress high-frequency actuator commands
C. It must integrate position error before the navigation loop generates waypoints
D. It must reject fast rotational disturbances before the slower attitude loop reacts

51 During a strong wind, a vehicle's commanded roll torque remains beyond actuator capability, so the rate controller's integral term grows continuously. When the wind drops, the vehicle overshoots severely. Which correction is most appropriate?

Introduction to autopilot System Hard
A. Increase the integral gain so accumulated error is removed more rapidly
B. Differentiate the saturated motor command and add it to the attitude target
C. Apply integral anti-windup using saturation-aware clamping or back-calculation
D. Disable actuator saturation so the controller can preserve its requested torque

52 An autopilot's estimator reports a GNSS velocity innovation of with innovation variance . For a normalized innovation squared gate of , how should this scalar measurement be handled?

Introduction to autopilot System Hard
A. Accept it because the normalized innovation squared is
B. Reject it because the normalized innovation squared is
C. Accept it because the normalized innovation squared is
D. Reject it because the normalized innovation squared is

53 A fixed-wing autopilot must track a ground path in steady crosswind. Airspeed is sufficient, but commanding the aircraft nose directly along the desired ground-track bearing causes lateral drift. What should the guidance system command?

Introduction to autopilot System Hard
A. A heading equal to the desired ground track regardless of measured wind
B. A yaw rate proportional only to the difference between airspeed and groundspeed
C. A wind-corrected heading that produces the desired ground-velocity direction
D. A bank angle of zero while increasing throttle until drift disappears

54 A stationary gyroscope has an uncompensated constant bias of . If attitude is obtained only by integrating its output, approximately how much attitude error accumulates in minutes?

Internal Sensors Hard
A.
B.
C.
D.

55 A multirotor accelerates horizontally at while remaining level. An attitude estimator temporarily treats the accelerometer as measuring gravity alone. Approximately what false tilt angle can this assumption introduce?

Internal Sensors Hard
A.
B.
C.
D.

56 Barometric altitude suddenly indicates a climb whenever rotor speed increases, even though GNSS and range measurements show constant altitude. Which mechanism and mitigation are most consistent with this behavior?

Internal Sensors Hard
A. Magnetic hard-iron bias; rotate the pressure sensor and recalibrate motor endpoints
B. Propeller-induced pressure changes; relocate the vent and add static-pressure shielding
C. Gyroscope scale-factor drift; increase barometer sampling and reduce gyro bandwidth
D. GNSS clock drift; seal the pressure port completely and disable temperature correction

57 Magnetometer heading error is small with motors off but increases predictably with total motor current. Which calibration model most directly targets this effect?

Internal Sensors Hard
A. Estimate a magnetic offset proportional to motor current and subtract it
B. Estimate a constant gyroscope bias during each high-throttle maneuver
C. Rotate GNSS velocity according to the commanded collective-thrust value
D. Scale accelerometer measurements according to measured battery voltage

58 During GNSS denial, an optical-flow sensor reports image motion in radians per second. Which additional measurement is most directly required to convert that angular flow into metric horizontal velocity over level ground?

External Sensors Hard
A. Receiver signal-to-noise ratio
B. Absolute magnetic field strength
C. Static atmospheric pressure
D. Height above the observed surface

59 A downward rangefinder measures distance along the body vertical axis while the vehicle is tilted by roll and pitch above flat terrain. Ignoring sensor offset, which expression gives vertical height?

External Sensors Hard
A.
B.
C.
D.

60 Near tall reflective buildings, a GNSS receiver reports high satellite count and a plausible position, but the position repeatedly jumps by several meters. Which evidence most strongly indicates multipath rather than normal vehicle motion?

External Sensors Hard
A. Optical-flow velocity and GNSS velocity agree throughout each reported position change
B. GNSS innovations jump while inertial predictions remain smooth and dynamically consistent
C. Gyroscope rates rise with matching accelerometer forces during every position displacement
D. Barometric altitude changes consistently with the three-dimensional GNSS trajectory